Operations & Maintenance Technician Job at Parking Network B.V. (Ostend)

Operations & Maintenance Technician

Responsible for the operation, routine servicing and care of a wide variety of s...

Location

United States , Manalapan Township

Salary:

35.76 USD / Hour

Veolia

Expiration Date

Until further notice

Requirements

High School Diploma or GED required, preferably supplemented by course work in chemistry, biology, mechanics, mathematics and/or technical school training
Must obtain/maintain New Jersey Department of Environmental Protection licenses as defined within the CBA
Possession of valid New Jersey driver’s license
Must be flexible and enjoy a diversity of responsibilities
Ability to interpret mechanical drawings, layouts, wiring diagrams, logic drawings, P&ID’s, technical manuals and specifications
Capable of completing written operating procedures, work requests and other documentation completion
Ability to prioritize and handle multiple tasks efficiently
Ability to diagnose abnormalities in complex controls, interlocked control schemes and other operating systems
Experience performing maintenance and operational tasks of substantial variety and complexity without close technical supervision
Must demonstrate and apply thorough knowledge of mechanical and/or electrical principles and practices and/or instrumentation and controls logics and diagnostics including troubleshooting skills

Job Responsibility

Operates, maintains, repairs and inspects water treatment systems to provide compliance with all applicable state and federal regulations maintaining optimum plant operations
Monitors all charts, gauges and other operating equipment via manual and electronic means such as a SCADA system
Ensures water quality meets minimum regulatory requirements. Calculates chemical feed rates required, calibrates chemical feed equipment and adjusts chemical feed rate to maintain consistent water quality
Maintains good housekeeping procedures at the plant. Performs routine housekeeping chores and special housekeeping as required
Conducts safety inspections and follows all safety rules and procedures
Ensures that pumping combinations are accomplished in the most economical manner or as directed by supervisor
Responsible for start-up, shutdown, operation and periodic checks of water treatment processes, components and equipment
Adjustments of plant equipment such as pumping systems, chemical feeders, auxiliary equipment and control system storage tanks levels and pump stations indicators
Performs operations in accordance with established SOPs and job safety standards
Develops, assists, and revises operations and maintenance related procedures

What we offer

paid time off policies
health, dental and vision insurance
employer sponsored 401(k) plan

Fulltime

Operations & Maintenance Technician

Crusoe is seeking a dedicated Operations & Maintenance Technician (OMT) to ensur...

Location

United States , Abilene

Salary:

33.00 - 38.00 USD / Hour

Crusoe

Expiration Date

Until further notice

Requirements

High School diploma or equivalent is required
Demonstrable knowledge of all facets of power plant operations and the ability to make competent decisions in emergency situations
Ability to read and interpret mechanical drawings, electrical one-lines, logic drawings, technical manuals, and P&IDs
Proficiency in troubleshooting mechanical, instrumentation, and electrical equipment, as well as operating welding and cutting equipment
Good verbal and written communication skills and proficiency in Microsoft Office, specifically Excel and Word
Ability to walk, reach, climb, and lift up to 50 pounds
Willingness to work 12-hour rotating shifts and availability for call-ins or work overload as needed
Must be authorized to work in the USA
This position is designated a safety-sensitive position and/or is located in a safety-sensitive facility. Drug and alcohol program participation is required.

Job Responsibility

Operate and maintain a simple cycle power generating facility and its auxiliary equipment, including heat recovery steam generators, air compressors, and fire suppression systems with minimal guidance
Identify and resolve CEMS problems, perform Root Cause Analysis of failures, and repair defective plant equipment such as pumps, valves, and gearboxes
Conduct "Inspection of Watch" on all plant systems and read meters or automatic devices to record temperatures, vibrations, fluid levels, and water chemistry to verify operating conditions
Perform analysis on HRSG, auxiliary boiler, and cooling tower systems
control chemical feed and blowdown rates to maintain proper control ranges
Open and close circuit breakers for system operation or electrical isolation, and perform piping and conduit installation for plant upgrades
Utilize the facility’s computerized maintenance management system (CMMS) and assist with the development of Operations and Maintenance procedures
Coordinate with vendors for chemical ordering and equipment repair, work with Plant Management on capital projects, and assist in administering the Operator training program
Perform general housekeeping, painting, and continuous improvement tasks to maintain the appearance and cleanliness of the plant and control room.

What we offer

Restricted Stock Units in a fast growing, well-funded technology company
Health insurance package options that include HDHP and PPO, vision, and dental for you and your dependents
Employer contributions to HSA accounts
Paid Parental Leave
Paid life insurance, short-term and long-term disability
Teladoc
401(k) with a 100% match up to 4% of salary
Generous paid time off and holiday schedule
Cell phone reimbursement
Tuition reimbursement

Fulltime

Operations & Maintenance Technician

Responsible for the operation, routine servicing and care of a wide variety of s...

Location

United States , Lambertville

Salary:

23.00 - 25.50 USD / Hour

Veolia

Expiration Date

Until further notice

Requirements

High School Diploma/GED is required
Preferably supplemented by course work in chemistry, biology, mechanics, mathematics and/or technical school training
Must obtain/maintain New Jersey Department of Environmental Protection licenses T-1 and W-1 within 3 years
Possession of valid New Jersey driver’s license
Upon completion of training, must have a strong technical knowledge of, and hands-on experience working in the operation of advanced water treatment plant facilities on an assigned shift
Must be flexible and enjoy a diversity of responsibilities
Thorough knowledge of the operating characteristics and maintenance requirements of water treatment plants
Knowledge of electrical and electronic systems: knowledge of hydraulic, chemical and mechanical principles pertinent to water treatment plant operations
Thorough knowledge of occupational hazards of the work and the necessary safety precautions
Ability to operate a computer and other electronic devices relative to the operation of the plants, troubleshooting malfunctions and recording data

Job Responsibility

Operates, maintains, repairs and inspects water treatment systems to provide compliance with all applicable state and federal regulations maintaining optimum plant operations
Monitors all charts, gauges and other operating equipment via manual and electronic means such as a SCADA system
Ensures water quality meets minimum regulatory requirements
Calculates chemical feed rates required, calibrates chemical feed equipment and adjusts chemical feed rate to maintain consistent water quality
Maintains good housekeeping procedures at the plant
Performs routine housekeeping chores and special housekeeping as required
Conducts safety inspections and follows all safety rules and procedures
Ensures that pumping combinations are accomplished in the most economical manner or as directed by supervisor
Responsible for start-up, shutdown, operation and periodic checks of water treatment processes, components and equipment
Adjustments of plant equipment such as pumping systems, chemical feeders, auxiliary equipment and control system storage tanks levels and pump stations indicators

What we offer

Paid time off policies
health, dental, vision, life insurance
savings accounts
tuition reimbursement
paid volunteering
employer sponsored 401(k) plan
Sick leave – 56 hours
Observed Holidays – 11 days
Vacation – 15 days
Eligible for up to 3.5% Annual Performance Bonus

Fulltime

Operations & Maintenance Technician

Responsible for the operation, routine servicing and care of a wide variety of s...

Location

United States , Lambertville

Salary:

25.00 - 27.00 USD / Hour

Veolia

Expiration Date

Until further notice

Requirements

High School Diploma/GED is required
Preferably supplemented by course work in chemistry, biology, mechanics, mathematics and/or technical school training
Must obtain/maintain New Jersey Department of Environmental Protection licenses T-1 and W-1 within 3 years
Possession of valid New Jersey driver’s license
Upon completion of training, must have a strong technical knowledge of, and hands-on experience working in the operation of advanced water treatment plant facilities on an assigned shift
Must be able to read and write
Ability to learn and apply new water industry technology
Must be flexible and enjoy a diversity of responsibilities
Thorough knowledge of the operating characteristics and maintenance requirements of water treatment plants
Knowledge of electrical and electronic systems: knowledge of hydraulic, chemical and mechanical principles pertinent to water treatment plant operations

Job Responsibility

Operates, maintains, repairs and inspects water treatment systems to provide compliance with all applicable state and federal regulations maintaining optimum plant operations
Monitors all charts, gauges and other operating equipment via manual and electronic means such as a SCADA system
Ensures water quality meets minimum regulatory requirements
Calculates chemical feed rates required, calibrates chemical feed equipment and adjusts chemical feed rate to maintain consistent water quality
Maintains good housekeeping procedures at the plant
Performs routine housekeeping chores and special housekeeping as required
Conducts safety inspections and follows all safety rules and procedures
Ensures that pumping combinations are accomplished in the most economical manner or as directed by supervisor
Responsible for start-up, shutdown, operation and periodic checks of water treatment processes, components and equipment
Adjustments of plant equipment such as pumping systems, chemical feeders, auxiliary equipment and control system storage tanks levels and pump stations indicators

What we offer

Paid time off policies
health, dental, vision, life insurance
savings accounts
tuition reimbursement
paid volunteering
employer sponsored 401(k) plan
Sick leave – 56 hours
Observed Holidays – 11 days
Vacation – 15 days
Eligible for up to 3.5% Annual Performance Bonus

Fulltime

Operations & Maintenance Technician

Crusoe is seeking a dedicated Operations & Maintenance Technician (OMT) to ensur...

Location

United States , Abilene

Salary:

33.00 - 38.00 USD / Hour

Crusoe

Expiration Date

Until further notice

Requirements

High School diploma or equivalent is required
Demonstrable knowledge of all facets of power plant operations and the ability to make competent decisions in emergency situations
Ability to read and interpret mechanical drawings, electrical one-lines, logic drawings, technical manuals, and P&IDs
Proficiency in troubleshooting mechanical, instrumentation, and electrical equipment, as well as operating welding and cutting equipment
Good verbal and written communication skills and proficiency in Microsoft Office, specifically Excel and Word
Ability to walk, reach, climb, and lift up to 50 pounds
Willingness to work 12-hour rotating shifts and availability for call-ins or work overload as needed
Must be authorized to work in the USA
This position is designated a safety-sensitive position and/or is located in a safety-sensitive facility. Drug and alcohol program participation is required.

Job Responsibility

Operate and maintain a Combined Cycle power generating facility and its auxiliary equipment, including heat recovery steam generators (HRSG), air compressors, and fire suppression systems with minimal guidance
Identify and resolve CEMS problems, perform Root Cause Analysis of failures, and repair defective plant equipment such as pumps, valves, and gearboxes
Conduct "Inspection of Watch" on all plant systems and read meters or automatic devices to record temperatures, vibrations, fluid levels, and water chemistry to verify operating conditions
Perform analysis on HRSG, auxiliary boiler, and cooling tower systems
control chemical feed and blowdown rates to maintain proper control ranges
Open and close circuit breakers for system operation or electrical isolation, and perform piping and conduit installation for plant upgrades
Utilize the facility’s computerized maintenance management system (CMMS) and assist with the development of Operations and Maintenance procedures
Coordinate with vendors for chemical ordering and equipment repair, work with Plant Management on capital projects, and assist in administering the Operator training program
Perform general housekeeping, painting, and continuous improvement tasks to maintain the appearance and cleanliness of the plant and control room.

What we offer

Restricted Stock Units in a fast growing, well-funded technology company
Health insurance package options that include HDHP and PPO, vision, and dental for you and your dependents
Employer contributions to HSA accounts
Paid Parental Leave
Paid life insurance, short-term and long-term disability
Teladoc
401(k) with a 100% match up to 4% of salary
Generous paid time off and holiday schedule
Cell phone reimbursement
Tuition reimbursement

Fulltime

Operations & Maintenance Technician II

Crusoe is seeking a skilled Operations & Maintenance Technician II (OMT II) to e...

Location

United States , Abilene

Salary:

41.00 - 47.00 USD / Hour

Crusoe

Expiration Date

Until further notice

Requirements

High School diploma or equivalent is required
Ability to read and interpret mechanical drawings, electrical one-lines, logic drawings, technical manuals, and P&IDs
Comprehensive knowledge of mechanical, instrumentation, and electrical equipment, including proficiency in repairing, replacing, and dismantling defective parts
Adept at diagnosing problems with mechanical equipment and performing water chemistry analysis
Strong verbal and written communication skills with the ability to train other personnel and write operating procedures
Capable of operating welding and cutting equipment, as well as tools such as drill presses, pipe threading machines, and grinders
Ability to perform walking, reaching, climbing, and lifting up to 50 pounds
Willingness to work a 12-hour rotating shift and be available for call-ins and work overload as needed
Must be authorized to work in the USA
This position is designated a safety-sensitive position and/or is located in a safety-sensitive facility. Drug and alcohol program participation is required.

Job Responsibility

Plant Operations & Maintenance: Operate and maintain simple cycle power generating facility equipment, including heat recovery steam generators, air compressors, and fire suppression systems, with minimal guidance or assistance
Technical Troubleshooting & Repair: Adeptly troubleshoot, diagnose, and repair defective plant equipment such as pumps, valves, fans, gearboxes, and turbine components in a timely fashion
System Inspections & Data Recording: Perform an "Inspection of Watch" on each plant system and record data from meters and gauges—including temperature, vibration, fluid levels, and water chemistry—to verify operating conditions
Water Chemistry Management: Perform analysis on HRSG, auxiliary boiler, and cooling tower systems, making necessary adjustments to chemical feed and blowdown rates to ensure chemistry remains within proper control ranges
Electrical & Mechanical Tasks: Responsible for opening and closing circuit breakers for system operation or electrical isolation, and performing piping and conduit installation for plant upgrades
Operational Documentation: Utilize the facility’s computerized maintenance management system (CMMS), assist with the development of O&M procedures, and write routine reports or work requests
Safety & Regulatory Adherence: Strictly adhere to all safety and environmental rules, facility safety programs, and plant environmental permits to protect personnel and public safety
Cross-Functional Collaboration: Coordinate with vendors for chemical ordering and timely equipment repairs, and assist in performing Root Cause Analysis (RCA) of failures
Continuous Improvement: Perform general housekeeping and painting projects to maintain the cleanliness and appearance of all plant areas and the control room.

What we offer

Restricted Stock Units in a fast growing, well-funded technology company
Health insurance package options that include HDHP and PPO, vision, and dental for you and your dependents
Employer contributions to HSA accounts
Paid Parental Leave
Paid life insurance, short-term and long-term disability
Teladoc
401(k) with a 100% match up to 4% of salary
Generous paid time off and holiday schedule
Cell phone reimbursement
Tuition reimbursement

Fulltime

Operations Maintenance Technician

The Operations Maintenance Technician supports Cardinal Health’s Sustainable Tec...

Location

United States , Riverview

Salary:

19.00 USD / Hour

Apex Systems

Expiration Date

Until further notice

Requirements

2–4 years of relevant maintenance or technical experience (preferred)
High School Diploma, GED, or equivalent
equivalent work experience also accepted
Technical diploma or Associate Degree in Electrical Systems, Mechanics, Manufacturing, or a related field (preferred)
Skilled in using precision measuring tools, power tools, and general workshop equipment
Strong mechanical aptitude with the ability to diagnose and resolve complex equipment problems
Working knowledge of related systems inside and outside core responsibility area
Ability to work independently and within a team in a regulated environment
Experience with Electrical and Pneumatic Systems

Job Responsibility

Apply knowledge of maintenance principles and company policies to complete a wide variety of technical tasks
Perform maintenance, testing, and repairs on equipment such as printers, packaging mechanisms, and semi‑automated systems
Use precision measuring devices, power tools, and workshop equipment safely and effectively
Troubleshoot mechanical and basic electrical issues, identifying root causes and implementing corrective actions
Maintain required licenses, certifications, and ongoing training
Meet preventive maintenance (PM) compliance requirements and complete quality‑related training
Work on moderately complex assignments requiring good judgment and problem‑solving skills
Review and provide feedback on processes for new assignments when appropriate
Support quality standards and ensure all work adheres to regulatory and facility guidelines
Work with limited supervision while producing consistent, high‑quality results

What we offer

medical
dental
vision
life
disability
other insurance plans
ESPP (employee stock purchase program)
401K program with company match after 12 months
HSA (Health Savings Account on the HDHP plan)
SupportLinc Employee Assistance Program (EAP) with up to 8 free counseling sessions

Fulltime

Operations & Maintenance Technician II

Crusoe is seeking a skilled Operations & Maintenance Technician II (OMT II) to e...

Location

United States , Abilene

Salary:

41.00 - 47.00 USD / Hour

Crusoe

Expiration Date

Until further notice

Requirements

High School diploma or equivalent is required
Ability to read and interpret mechanical drawings, electrical one-lines, logic drawings, technical manuals, and P&IDs
Comprehensive knowledge of mechanical, instrumentation, and electrical equipment, including proficiency in repairing, replacing, and dismantling defective parts
Adept at diagnosing problems with mechanical equipment and performing water chemistry analysis
Strong verbal and written communication skills with the ability to train other personnel and write operating procedures
Capable of operating welding and cutting equipment, as well as tools such as drill presses, pipe threading machines, and grinders
Ability to perform walking, reaching, climbing, and lifting up to 50 pounds
Willingness to work a 12-hour rotating shift and be available for call-ins and work overload as needed
Must be authorized to work in the USA
This position is designated a safety-sensitive position and/or is located in a safety-sensitive facility. Drug and alcohol program participation is required

Job Responsibility

Operate and maintain Combined Cycle power generating facility equipment, including heat recovery steam generators (HRSG), air compressors, and fire suppression systems, with minimal guidance or assistance
Adeptly troubleshoot, diagnose, and repair defective plant equipment such as pumps, valves, fans, gearboxes, and turbine components in a timely fashion
Perform an "Inspection of Watch" on each plant system and record data from meters and gauges—including temperature, vibration, fluid levels, and water chemistry—to verify operating conditions
Perform analysis on HRSG, auxiliary boiler, and cooling tower systems, making necessary adjustments to chemical feed and blowdown rates to ensure chemistry remains within proper control ranges
Responsible for opening and closing circuit breakers for system operation or electrical isolation, and performing piping and conduit installation for plant upgrades
Utilize the facility’s computerized maintenance management system (CMMS), assist with the development of O&M procedures, and write routine reports or work requests
Strictly adhere to all safety and environmental rules, facility safety programs, and plant environmental permits to protect personnel and public safety
Coordinate with vendors for chemical ordering and timely equipment repairs, and assist in performing Root Cause Analysis (RCA) of failures
Perform general housekeeping and painting projects to maintain the cleanliness and appearance of all plant areas and the control room

What we offer

Restricted Stock Units in a fast growing, well-funded technology company
Health insurance package options that include HDHP and PPO, vision, and dental for you and your dependents
Employer contributions to HSA accounts
Paid Parental Leave
Paid life insurance, short-term and long-term disability
Teladoc
401(k) with a 100% match up to 4% of salary
Generous paid time off and holiday schedule
Cell phone reimbursement
Tuition reimbursement

Fulltime

Select Country

Operations & Maintenance Technician

Job Description

Job Responsibility

Requirements

Nice to have

Looking for more opportunities?

Operations & Maintenance Technician

Operations & Maintenance Technician

Operations & Maintenance Technician

Operations & Maintenance Technician

Operations & Maintenance Technician

Operations & Maintenance Technician

Operations & Maintenance Technician II

Operations Maintenance Technician

Operations & Maintenance Technician II

Our AI answers in your language